Gain Omni

Reportlinker Adds Global Aerospace and Defence Industry Industry
Reportlinker.com announces that a new market research report is available in its catalogue:

Cell Phone Signal Boosters: All Of The Pieces Explained

Cell phone signal boosters, also called amplifiers or repeaters, work by capturing a weak cell signal outside the home, office, car, boat, warehouse, etc, bring it inside, amplify it, and redistribute it. The most popular products on the market contain four main components: the outside antenna, the amplifier (booster / repeater),the inside antenna, and the cabling to connect everything.

The Outside Antenna

The outside antenna can be omni-directional (can capture signal from all directions) or directional (works best when pointed directly at a cell tower). The benefit to omni-directional antennas is that they are easy to install and pick up/radiate signals in a 360 degree horizontal plane. They are great for picking up and transmitting to multiple towers for multiple carriers. You want to mount them as high as possible where the signal is strongest. A couple disadvantages of omni-directional antennas: 1) their gain is typically lower than directional antennas. 2) They are more prone to other RF interference. TheCellphone-Mate CM100-Sis a good example of a popular omni-directional outdoor antenna.

The benefit to directional antennas (Yagi antennas) is that they typically provide more signal gain (power) than omni-directional antennas. They are also less prone to other RF interference. Because they provide more gain, the tower can typically be much further away than is acceptable for an omni-directional antenna. The Wilson 304411 Wide Band Yagi is a good example of a popular directional outdoor antenna.

The Amplifier

Just about every amplifier (or booster) will have two values that basically define it. The first is "band". Most amplifiers are classified as single band or dual band. With the exception of iDEN (Nextel), single band refers to either 850 MHz or 1900 MHz, meaning that the amplifier only boosts one of those two frequency ranges. Dual band on the other hand will boost both frequency ranges. While there are certainly reasons for purchasing a signal band booster, dual band boosters are more common and compatible with just about every carrier.

The second value is gain and just about every signal amplifier will have this specification published. Without getting too technical, gain is defined as the ratio of output to input. When specifying electrical power, gain is measured in decibels or dB. dB numbers are derived from a fairly simple logarithmic function; however all you need to know is that every increase in 3 dB doubles the power.

10 dB = gain of 10
13 dB = gain of 20
16 dB = gain of 40
19 dB = gain of 80
20 dB = gain of 100
30 dB = gain of 1,000
40 dB = gain of 10,000
50 dB = gain of 100,000
60 dB = gain of 1,000,000

If you have been shopping around for a cell phone signal booster then you have probably come across these numbers and were not sure exactly what they meant. Now, hopefully you have a better understanding.

When searching for an amplifier for your particular application, please reference the following:

20 dB - Automobile, Boat - 4ft. antenna separation or direct connect

30 dB - Automobile, Boat - 5ft. antenna separation or direct connect

40-45 dB - Large Auto, RV, Large Boat - 6ft. to 20ft. antenna separation

50 dB - Small Home, Townhouse, Office - 40ft. to 60ft. antenna separation

55 dB - Medium Home, Office - 50ft. to 70ft. antenna separation

60+ dB - Large Home, Office, Warehouse - 70+ft. antenna separation

Please keep in mind that this table represents general rules of thumb and the recommended applications and distances may vary by manufacturer. Antenna separation is very important and should not be overlooked when choosing or designing your system. Antenna separation is the straight line distance (in 3 dimensions) from the outside antenna to the inside antenna. In practice, these distances can be somewhat shorter than the rule-of-thumb distances listed above due to ceilings, walls, fireplaces, metal roofs, brick fireplaces, etc. blocking or inhibiting a straight-line signal path. The rule of thumb antenna separation distances are to keep your amplifier from going to oscillation. In the audio world, this is analogous to getting a microphone too close to a speaker and producing feedback.

The Inside Antenna

Inside antennas, just like outside antennas, come in different shapes and sizes, serve different purposed and can be omni-directional or directional. A lot of the products from Wireless Extenders (Wi-Ex) have a small omni-directional antenna attached to the amplifier itself. While this makes installation fairly simple, the unit must become part of your home dcor as it must be installed in a central location and will be visible. Most in-building products from manufacturers such as Cellphone-Mate, Digital Antenna, and Wilson Electronics will have a separately mounted internal antenna.This may sometimes make them more difficult to install, but having a separate indoor antenna allows for the most flexibility when choosing a central coverage point. The most popular antenna for providing omni-directional internal coverage is the ceiling-mounted dome antenna, such as the Cellphone-Mate, Inc. CM222. They even make low-profile dome antennas and even dome antennas which resemble light fixtures, which are less obtrusive and mesh well with any home dcor.

Inside antennas can be directional as well. Wall-mounted panel antennas provide directional coverage in typically a 90-120 degree radiation pattern. While coverage is only provided pretty much in front of a directional antenna they usually offer more gain than a dome antenna. With that being said, panel antennas are great for large but somewhat narrow rooms or hallways. They are also useful if you are not able to fully adhere to the antenna separation requirements. If the indoor directional antenna is pointed away from the outdoor antenna you will most likely be able to get away with a less than recommended antenna separation distance.

The Cabling

The cabling and connectors used to connect the outside antenna to the amplifier, as well as the inside antenna to the amplifier, play a crucial role in how your system will perform. Depending on the product, different types of cabling and connectors can be used. Some of the Wi-Ex and Wilson Electronics products use standard RG6 or RG59 75 Ohm coax. This is the same coax used for your cable TV or satellite system. While this type of cabling is less expensive, there are some drawbacks. For cellular and PCS frequencies, on average, RG6 will lose 6-10 dB of signal per 100ft.Depending on the actual length of cable you use, this can sometimes provide more signal loss than the outside antenna provides in gain. Remember, you want your amplifier to receive the highest level of signal possible. For this reason, it is recommended that runs using RG6 should be no longer than 50 or 60 ft. For most other in-building cell phone signal boosters LMR-400 50 Ohm Coax is the standard. In comparison, while LMR-400 is more expensive and thicker, it only loses about 3-6 dB per 100 ft for cellular and PCS frequencies respectively. Based on this, LMR-400 can be run further than RG6 before there is a decrease in system performance. For all three-piece systems (outside antenna, amplifier, inside antenna) it is recommended the amplifier be installed as close to the external antenna as possible, using the shortest cable possible. Ex. If the external antenna is installed on a roof, it is recommended the amplifier be installed in the attic as opposed to the basement. The shorter the cable length between the external antenna and the amplifier, the better. Remember that there is no separation requirement between the antennas and the amplifier, only between the antennas.

Thinking about purchasing a cell phone signal booster? Please check out the author resource box for more information.

About the Author

Article provided by Ryan Jackson, owner of
MyCellSignalBooster.Com
, a store dedicated to providing high quality and affordable
cell phone signal boosters and accessories
from manufacturers such as Wi-Ex, Digital Antenna, Cellphone-Mate, and Wilson Electronics.

Incoming Searches:

Alfa 9dBi WiFi Booster SMA OMNI-Directional High-Gain Screw-On Swivel Antenna With magnetic base for Alfa - WUS036H WUS036H1W